Proven oilfield technology: oilfield casing in ~12 m sections, top of the structure to the cutter head. Sizes from 7" to 30", L80: grades, materials and weights per foot are all available off the shelf.
The tension tubular is standard oilfield casing, run in wells worldwide to API 5CT. It comes in sizes from 7" to 30" outside diameter, with grades, materials and weights per foot already made by the oil and gas industry: 7" to 20" is API 5CT casing, made in L80; 24" to 30" is conductor casing, made in the grade ordered. Each design picks the size and weight its tension needs.
| Size (OD) | mm | Typical weights (lb/ft) | Note |
|---|---|---|---|
| 7" | 177.8 | 17–26 | Production casing; 7" 26 lb/ft L80 is a stock item1,2 |
| 9-5/8" | 244.5 | 40–47 | Common production casing1 |
| 13-3/8" | 339.7 | 68–82 | Large-diameter surface casing1 |
| 20" | 508.0 | to 133 (API 5CT) | Largest API 5CT casing size; the MMC drawings show 20"3 |
| 26" | 660.4 | 202–392 | Conductor casing, 0.75" to 1.5" wall4 |
| 30" | 762.0 | 234–598 | Conductor casing, 0.75" to 2" wall4 |
Pipe body yield strength is the tension the pipe body carries at minimum yield: F = π/4 × (OD² − ID²) × minimum yield strength (API 5C3 method).9 Figures below use 80 ksi (552 MPa), the L80 minimum yield.
| Size (OD) | Weight (lb/ft) | Wall (in) | Pipe body yield (1,000 lb) | kN | Tonnes-force |
|---|---|---|---|---|---|
| 7" | 23 | 0.317 | 532 | 2,368 | 242 |
| 7" | 26 | 0.362 | 604 | 2,686 | 274 |
| 9-5/8" | 40 | 0.395 | 916 | 4,076 | 416 |
| 9-5/8" | 47 | 0.472 | 1,086 | 4,830 | 493 |
| 13-3/8" | 68 | 0.480 | 1,556 | 6,920 | 706 |
| 13-3/8" | 72 | 0.514 | 1,661 | 7,390 | 754 |
| 20" | 133 | 0.635 | 3,091 | 13,747 | 1,402 |
| 26"* | 202–392 | 0.75–1.5 | 4,760–9,236 | 21,171–41,085 | 2,159–4,190 |
| 30"* | 234–598 | 0.75–2.0 | 5,513–14,074 | 24,525–62,606 | 2,501–6,384 |
Assumptions: nominal wall, no wall tolerance or corrosion allowance; pipe body only, the connection rating is set by the connection chosen; walls for 7" to 20" from the API casing tables.10 *26" and 30" are conductor casing; figures assume it is ordered at 80 ksi minimum yield. Design factors are set in detailed design.
The same sizes are made in every API 5CT grade. L80 is the baseline; a higher grade carries more tension in the same pipe.7,8
| Grade | Yield strength, min–max | Tensile strength, min | Tension vs L80 | Use in the oilfield |
|---|---|---|---|---|
| J55 / K55 | 379–552 MPa (55–80 ksi) | 517 / 655 MPa (75 / 95 ksi) | 0.69× | Surface casing |
| N80 | 552–758 MPa (80–110 ksi) | 689 MPa (100 ksi) | 1.00× | General, deeper wells |
| L80 | 552–655 MPa (80–95 ksi) | 655 MPa (95 ksi) | 1.00× (baseline) | Sour service, controlled hardness; Type 1, 9Cr, 13Cr |
| C90 | 621–724 MPa (90–105 ksi) | 689 MPa (100 ksi) | 1.13× | Sour service |
| T95 | 655–758 MPa (95–110 ksi) | 724 MPa (105 ksi) | 1.19× | Sour service |
| P110 | 758–965 MPa (110–140 ksi) | 862 MPa (125 ksi) | 1.38× | Deep, high-pressure wells |
| Q125 | 862–1,034 MPa (125–150 ksi) | 931 MPa (135 ksi) | 1.56× | Ultra-deep, high-pressure wells |
Tension vs L80 is the ratio of minimum yield strengths, for the same size and wall. MPa converted from ksi (1 ksi = 6.895 MPa).
| Design | Per unit | Per km | Mass each | Mass, all per unit |
|---|---|---|---|---|
| MMC-VC | 2 per pylon | 80 | 0.9 t | 1.7 t per pylon |
| MMC-VB | 6 per pylon | 240 | 2.9 t | 17.3 t per pylon |
| MMC-VA | 12 per pylon | 480 | 2.6 t | 31.6 t per pylon |
| MMC-VD | 8 per pylon | 320 | 2.9 t | 23.4 t per pylon |
| MMC-TB | 6 per tower | 30 | 2.8 t | 16.5 t per tower |
| MMC-TB Guyed | 6 per tower | 30 | 2.8 t | 16.5 t per tower |
| MMC-TA | 12 per portal | 60 | 2.8 t | 33.1 t per portal |
From the MMC-DWG-005 bills of materials. Masses are estimates; "—" means not yet set.